Stable release of AxxSolder 3.6.1

• Add Set temp to plot
• Implement Standby delay [s] setting
• Implement graphing in landscape display mode

Previous release of AxxSolder 3.6.0
IMPORTANT!
As This firmware update re-arrange the user settings previous settings such as calibration data values will be lost.

• Implement graph display option
• Update menu system to groups
• Implement user setting for Delta T detection
• Fix plotting of fahrenheit

Previous release of AxxSolder 3.5.2

• Make current power unit % or W a user setting
• make a setting detect_nt115 in order to detect nt115 handles, this requires a mod to the JBC ADS stand
• Update power limit function

Previous release of AxxSolder 3.5.1

• Add power percent to bottom of bar graph
• Make changed parameters RED and default parameters WHITE
• Minor code updates for readability and performance

Previous release of AxxSolder 3.5.0

• Improvements on the menu system to improve speed and rendering (Thanks to Vetal!)
  Initial working new menu system
• Improve fault detection at earth faults and delta temperature
  Request power zero at earth fault
  Improve delta temp fault detection
• Fix screen rotation settings to 0, 90, 180, 270 deg
  Fix screen rotation setting
• Improve code comments
  Improve code comments
• Beep at set temp also when new temp is set
  Beep when temp is reached also if a new temp is set
• Use "Beep at set temp" as default
  Use Beep_At_Set_temp as default
• Add new improved beep tones
  Add user setting for different beep-tones
• Fix bug that cases random characters when long-pressing buttons in menu
• Add BAV199WQ Schematic symbol to project lib
  -Update BOM to 3.2 and small layout fix
• Add setting for momentary stand

Previous release of AxxSolder 3.4.2

• Fix GUI bug not rendering the GUI correctly when in landscape mode
  Add fix to GUI bug when in landscape mode

Previous release (AxxSolder v3.4.1)

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode

Stable release of AxxSolder 3.6.0
IMPORTANT!
As This firmware update re-arrange the user settings previous settings such as calibration data values will be lost.

• Implement graph display option
  
• Update menu system to groups
• Implement user setting for Delta T detection
• Fix plotting of fahrenheit

Previous release of AxxSolder 3.5.2

• Make current power unit % or W a user setting
• make a setting detect_nt115 in order to detect nt115 handles, this requires a mod to the JBC ADS stand
• Update power limit function

Previous release of AxxSolder 3.5.1

• Add power percent to bottom of bar graph
• Make changed parameters RED and default parameters WHITE
• Minor code updates for readability and performance

Previous release of AxxSolder 3.5.0

• Improvements on the menu system to improve speed and rendering (Thanks to Vetal!)
  Initial working new menu system
• Improve fault detection at earth faults and delta temperature
  Request power zero at earth fault
  Improve delta temp fault detection
• Fix screen rotation settings to 0, 90, 180, 270 deg
  Fix screen rotation setting
• Improve code comments
  Improve code comments
• Beep at set temp also when new temp is set
  Beep when temp is reached also if a new temp is set
• Use "Beep at set temp" as default
  Use Beep_At_Set_temp as default
• Add new improved beep tones
  Add user setting for different beep-tones
• Fix bug that cases random characters when long-pressing buttons in menu
• Add BAV199WQ Schematic symbol to project lib
  -Update BOM to 3.2 and small layout fix
• Add setting for momentary stand

Previous release of AxxSolder 3.4.2

• Fix GUI bug not rendering the GUI correctly when in landscape mode
  Add fix to GUI bug when in landscape mode

Previous release (AxxSolder v3.4.1)

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode

Stable release of AxxSolder 3.5.2

• Make current power unit % or W a user setting
• make a setting detect_nt115 in order to detect nt115 handles, this requires a mod to the JBC ADS stand
• Update power limit function

Previous release of AxxSolder 3.5.1

• Add power percent to bottom of bar graph
• Make changed parameters RED and default parameters WHITE
• Minor code updates for readability and performance

Previous release of AxxSolder 3.5.0

• Improvements on the menu system to improve speed and rendering (Thanks to Vetal!)
  Initial working new menu system
  
• Improve fault detection at earth faults and delta temperature
  Request power zero at earth fault
  Improve delta temp fault detection
• Fix screen rotation settings to 0, 90, 180, 270 deg
  Fix screen rotation setting
• Improve code comments
  Improve code comments
• Beep at set temp also when new temp is set
  Beep when temp is reached also if a new temp is set
• Use "Beep at set temp" as default
  Use Beep_At_Set_temp as default
• Add new improved beep tones
  Add user setting for different beep-tones
• Fix bug that cases random characters when long-pressing buttons in menu
• Add BAV199WQ Schematic symbol to project lib
  -Update BOM to 3.2 and small layout fix
• Add setting for momentary stand

Previous release of AxxSolder 3.4.2

• Fix GUI bug not rendering the GUI correctly when in landscape mode
  Add fix to GUI bug when in landscape mode

Previous release (AxxSolder v3.4.1)

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder 3.5.1

• Add power percent to bottom of bar graph
• Make changed parameters RED and default parameters WHITE
• Minor code updates for readability and performance

Previous release of AxxSolder 3.5.0

• Improvements on the menu system to improve speed and rendering (Thanks to Vetal!)
  Initial working new menu system
  
• Improve fault detection at earth faults and delta temperature
  Request power zero at earth fault
  Improve delta temp fault detection
• Fix screen rotation settings to 0, 90, 180, 270 deg
  Fix screen rotation setting
• Improve code comments
  Improve code comments
• Beep at set temp also when new temp is set
  Beep when temp is reached also if a new temp is set
• Use "Beep at set temp" as default
  Use Beep_At_Set_temp as default
• Add new improved beep tones
  Add user setting for different beep-tones
• Fix bug that cases random characters when long-pressing buttons in menu
• Add BAV199WQ Schematic symbol to project lib
  -Update BOM to 3.2 and small layout fix
• Add setting for momentary stand

Previous release of AxxSolder 3.4.2

• Fix GUI bug not rendering the GUI correctly when in landscape mode
  Add fix to GUI bug when in landscape mode

Previous release (AxxSolder v3.4.1)

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder 3.5.5

• Improvements on the menu system to improve speed and rendering (Thanks to Vetal!)
  Initial working new menu system
  
• Improve fault detection at earth faults and delta temperature
  Request power zero at earth fault
  Improve delta temp fault detection
• Fix screen rotation settings to 0, 90, 180, 270 deg
  Fix screen rotation setting
• Improve code comments
  Improve code comments
• Beep at set temp also when new temp is set
  Beep when temp is reached also if a new temp is set
• Use "Beep at set temp" as default
  Use Beep_At_Set_temp as default
• Add new improved beep tones
  Add user setting for different beep-tones
• Fix bug that cases random characters when long-pressing buttons in menu
• Add BAV199WQ Schematic symbol to project lib
  -Update BOM to 3.2 and small layout fix
• Add setting for momentary stand

Previous release of AxxSolder 3.4.2

• Fix GUI bug not rendering the GUI correctly when in landscape mode
  Add fix to GUI bug when in landscape mode

Previous release (AxxSolder v3.4.1)

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder 3.4.2

• Fix GUI bug not rendering the GUI correctly when in landscape mode
  Add fix to GUI bug when in landscape mode

Previous release (AxxSolder v3.4.1)

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder v3.4.1

• Fix of bug causing un-controlled heating if entering the settings menu while in run mode (heating mode).
  Fix bug which turned on heating to max if going into the main menu wh…

This is a vital bug fix and the new firmware should be flashed in order to prevent fatal damage to the installed cartridge.
The firmware affected by this bug is firmware v3.4.0.
A guide on how to upload a new firmware over SWD or USB can be found here:
Firmware update

Thanks to user Vetal on the Discord Group chat who found and pointed out this bug!

Previous release (AxxSolder v3.4.0)

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder v3.4.0

• Introduce a setting to turn on a short beep when the set temperature is reached
  Implement beep-at-set-temperature function

• Enter the settings menu from long-pressing the encoder button
  Implement long-press SW_1 to go to main menu

• Update the preset temperature by long-pressing the specific preset button
  Implement long-press SW_2 and SW_3 to set current set temp to new preset temperature

• The HAL_delay(2000) in the pop-up function is replaced with a HAL_tick-based counter
  remove HAL_delay(2000) from show_popup and make the show-time based on a HAL_GetTick() counter

• Update in hardware to AxxSolder hw 3.2 with series resistors on the output filter from the op-amps. Also update BOM.

Previous release of (AxxSolder v3.3.1)

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder v3.3.1

• Fix bug that did not let user use the two buttons to go up/down in the menu. It was therefore impossible to choose "3-button-mode" when you did not have the encoder.

• Small updates on the 3-button-mode navigation layout

Previous release (AxxSolder v3.3.0):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode
  

Stable release of AxxSolder v3.3.0

Changes from previous release (AxxSolder v3.2.4):

• Fix memory corruption bug from previous releases caused by user flash over writing sysem flash
  Put user flash at ADDR_FLASH_PAGE_63 instead of ADDR_FLASH_PAGE_62

• Implement a 3-button mode that allows the user to use three buttons instead of 2 buttons + 1 encoder. Changes the preset buttons to temp UP and DOWN. This makes the AxxSolder truly portable and fits in a pocket without the encoder sticking up.
  Implement 3-button mode